Do Car Speakers Get Quieter over Time? [Solution]

Published: 09/14/22 •  6 min read

Suppose your car’s speakers are a bit quieter or become quieter when you turn up the volume to maximum for your music player. In that case, you will not be able to experience the fullest potential of music to your favorite beats.

This is normal and expected, especially if you have had the same car for a few years or more.

In this article, we will discuss why this happens and how to fix it. 

Why Did My Car Speakers Get Quiet?

Quite a few things can cause your car’s speakers to become damaged over time. Some common culprits include:

Heat– The heat from the sun or other different sources will eventually damage your speaker cone, making it harder or impossible for sound waves to move through the speaker system. If you live in a hot climate, try keeping them out of direct sunlight as much as possible.

Water damage- Even if you have never had an issue with water getting into your door panels or dashboard, there is always a chance that something could happen during a rainstorm or snowstorm. It may cause some water to seep into your vehicle’s interior—especially if there was already some moisture present before those heavy rains or snows began falling! 

How To Fix Car Speakers That Are Quiet On Full Volume?

The best option is to set up an external amplifier to deliver high-end power to your car’s front and rear speakers. This can save you from swapping out the CD player in your vehicle for a more powerful amplifier, which could result in an expensive alternative.

Your car’s aftermarket speakers are quiet at full volume because you are under-powering the speakers. This is a common error that is often common in the world of car audio. 

Suppose you are choosing an external 4-channel amplifier to drive your front speakers. In that case, it is essential to make sure that it is compatible with the RMS that the speakers are intended to handle, as overpowering them can damage the voice coil inside the speakers.

Once you have determined the car amplifier you would like to set up to repair your car stereo with very low volume, which makes your car speakers sound so quiet, you will require a wiring kit. 

There are various kits to suit different configurations. Most 4-channel amps will be compatible and equipped with eight gauges of power. Let’s now discuss how to put an amplifier in your car to eliminate the extremely quiet sound of your speakers.

Connecting Powers

It is necessary to connect the red power through your car’s side panels and connect it to the + of your car’s battery.

Be sure to connect the fuse holder adjacent to the car battery to ensure it’s protected from wiring in the car. You will then be required to connect the opposite side of the red power cable to the 12 volts connector for the vehicle amp.

Connect Car AMP

You will need to connect the car amp to the ground on the right side. Connect the black wire onto the bolt, set it to a metal surface, and ensure that you have cleaned the paint off for the most effective connection.

If there’s still paint, the car amp may not start up the first time it is installed—the other wire from the ground to the ground terminal of the amp in your vehi

cle.

Connect X2 sets

It is necessary to connect X2 sets of long RCA cables on the other side of the power wire to prevent any unintentional sounding buzzing or humming from your speakers, which are classified as interference. They are connected to the rear and front preamp outputs at the rear of your stereo.

The other ends go into the amp in your car RCA inputs. It would help if you also connect the blue remote wire to the rear of the wiring harness for your music player. Connect the other end to the car amp’s turn-on wire for the remote. This part controls the amp to turn off when you turn on your car engine.

Connecting the speakers’ wires

The only thing left to figure out is connecting the speakers’ wires.

You will have the cutting four lengths of premium sixteen gauge wire for your speaker, then put them through your doors, connecting them to the car speakers.

You can use the wiring within the car’s wiring loom and plug them into the connections within the DIN slot. This can help you save time and your efforts since there is no need to go through every door to make connections. However, if you want the best sound quality, it’s ideal to get it right on the first attempt.

In general, using a 4- channels amplifier that powers your vehicle speaker will allow for louder sound when you turn up the volume in the car stereo. It will sound more apparent as it is not as distorted as produced in the sound.  

What Are Alternatives to Fix the Car Speaker Problem?

There are other options for fixing this problem.

You can’t really fix car speakers that are broken and need to be replaced.

If you have tried everything and your car speakers still aren’t working, you probably need to buy new ones. You can find replacement speakers at most auto parts stores and online retailers.

The best thing to do is to take your old speaker into the store with you so that they can match it up with a new one. Then, just remove the wires from both sides of the old speaker and wire up your new one!

How to Replace Car Speakers? 

If your car speakers are not working correctly or simply not loud enough, they need to be repaired or replaced. You can repair them yourself or take them to a professional mechanic to get the job done correctly.

Here’s how to replace a car speaker:

Remove the speaker from the door by disconnecting any wiring and unscrewing it from its place (make sure you don’t lose any screws).

Install a new speaker in its place and connect wires back into place. Secure the speaker with screws and put everything back together again.

Wrapping Up

We hope this article was helpful to you. The next time your speakers get quieter over time, don’t hesitate to check the connections and replace any damaged ones.

You can also try reconnecting them in different patterns (e.g., + – or – +). If that doesn’t work out, it might be time for a new set of speakers!